OXYGEN….

… we use it in a more
POWERFUL way.

EX-TRAFLAME®

an oxy-fuel cutting torch
developed by THERMACUT®

POWER OF OXYGEN

Do not waste oxygen for breathing only.

EX-TRAFLAME® PRODUCTS

SPECIAL O-RINGS TO AVOID MIXING OF GASSES

EX-TRAFLAME®

Uses standard replacement parts suitable for model HARRIS® consumables.

A-2100-A for acytelene and A-2100-PM for propane, natural gas and mixed gasses.

Torches A-2100-A and A-2100-PM are available with input fittings which are removable.

EX-TRAFLAME® PRO

Uses replacement parts suitable for model VADURA® and GRICUT® consumables with our unique design.

Greater cutting speed and lower preheating time.

A-1100-A for acetylene and A-1100-PM for propane, natural gas and mixed gasses.

EX-TRAFLAME® OXY-FUEL CUTTING SYSTEM

Reductions (9/16 -18 UNF / 9/16 -18 UNF / 9/16 -18 UNF LH) – only for A-2100-A/PM

Gases input (G 1/4“ / G 3/8“ / G 3/8“LH)

Fixing nut

Changeable injector (A – Acetylene, PM – Propane and natural gas)

Torch body

Torch head

Cutting tip

Heating nozzle

Consumables holder

Reductions (9/16 -18 UNF / 9/16 -18 UNF / 9/16 -18 UNF LH) – only for A-2100-A/PM

Gases input (G 1/4“ / G 3/8“ / G 3/8“LH)

Fixing nut

Changeable injector (A – Acetylene, PM – Propane and natural gas)

Torch body

Torch head

Cutting tip

Heating nozzle

Consumables holder

THERMACUT® CONSUMABLE CASE

SUITABLE FOR EX-TRAFLAME® AND EX-TRAFLAME® PRO

Item description:

Our sales representatives now present the whole EX-TRAFLAME® system in these display cases, where you can find everything necessary for your OXY-FUEL cutting table.

Order information:
EX-TRAFLAME®  order number: A-2222-PM
EX-TRAFLAME® PRO order number A-1111-PM

PROMO VIDEOS

HELPFUL VIDEOS

 

PRODUCT ARTICLES

ASSESSMENT OF OXY-FUEL CUT QUALITY

What to look for during oxy-fuel cutting and assessment of the cut quality? Thermacut® can reveal some of the typical cut quality errors that are commonly experienced, their cause and a few tips on how to eliminate them. Although, the oxy-fuel cutting process is considered to be quite a simple one, sometimes operators can be faced with cut quality issues. There are 4 main points to focus on when assessing cut quality. Poor cut edge profile The primary check should be to examine the cut edge of the workpiece. When correctly cut the workpiece should have a clean sharp to very slightly...

Read more

HANDHELD TORCH FOR EX-TRAFIRE® SD AND HD CUTTING SYSTEMS

A few years ago the Thermacut® Group decided to develop an original brand and its own products. Originality is a term that sounds good and it is nice to talk about it, but on the other hand it forces the creators of new products to surpass known limits and to look for new technical solutions for technology that has been known for more than 70 years. The plasma torch is an important component that defines how quickly and how well we can cut, what the costs related to the operation of plasma system will be, and if the client will be satisfied. Let's look at the torch handle, a key part that...

Read more

DOCUMENTS

Download details in pdf. If you are looking for more details, contact us

SAFETY AND OPERATING INSTRUCTIONS
EX-TRAFLAME® BROCHURE
OXY-FUEL CATALOG
WARRANTY

FAQ

Have a question? You can find the answers for the most common questions asked by our customers.

How to install EX-TRAFLAME® torch

How to replace the injector

How to set up the right flame

How to install consumables

The flame does not have enough power

What is the lifetime of the nozzles and how to improve it?

Lifetime of the consumables depends on the number of the piercings and the piercing process itself. The most important thing is to set up the „piercing speed“ of the torch, this condition eliminates the splitters comming back from the material to the consumables.

If you cannot find the answer to your specific question, please call us or send email: